Green Chemical Recovery
Solvent Recycling Machine are distillers which allow the recycling and the re-use of degreasing and washing solvents.Through a simple distillation process, they separate the contaminants (resins, polymers, pigments, paints, oils, etc.) from the original solvent.The boiling of the solvent is accomplished by a peripheral heating jacket filled with diathermic oil, heated by an electrical element.
The vapours are then convoyed to a condenser cooled by air or water. The condensed solvent is collected in a tank, for its reuse.
Calstar Solvent Recycling Machine is used for recovery the waste solution resulting from the following: automobile manufacturing and repair industry; electronic products manufacturing industry; precision instruments and hardware manufacturing industry; sports equipment manufacturing industry; shoe material industry; plastic materials; printing industry; manufacture of chemical coatings; FRP products industry; jewelry industry; optical products; etc.
GREEN CHEMICAL RECYCLING UNIT
FLEXO SOLVENT RECOVERY PLATEMAKING MACHINE
For Solvent Washout :
Recovering Unit For Any Environment
General explanation :
This Recycling Unit Designed for Flexography Photopolymer Platemakers.With Use of Solvent washout chemical and any ecological green chemical with specialties of distilling and cooling with cold air circulation and drain out of residue for high speed revival. Also Can be connected with in-line processor and any plate washout machine directly. Equipped with air-cooling / circulation and drain off the residue directly from a valve. Excellent recovering rate in the shortest time. It is perfect and high efficient recovery unit for flexography.
Technical Information :
Model No: FIP 30 LTR
FOR (PCE + BUTNOL)
85 % Ratio (FLEXO CHEMICAL PROCESSOR)
FLEXO CHEMICAL PROCESSOR FIP 30 LTR / FIP 60 LTR / FIP 80 LTR / FIP 100 LTR / FIP 200 LTR
|Recovery volume||Power consume||Diathermic oil||Machine dimension||Recovery rate|
|30 / 60 liters||220V 4.65KW||15 KG||1100x780x1200mm||85%|
|Model||Capacity / L||Voltage Power||Dimension / MM||Oil / Kg||N/W Kg|
FLEXO CHEMICAL PROCESSOR FIP 30 LTR / FIP 60 LTR / FIP 80 LTR / FIP 100 LTR / FIP 200 LTR Advantages & Operating Steps
Solvent Recovery Systems advantages:
• Reduce your solvent disposal costs and wastewater treatment surcharges
• 1 year or better payback on most solvent recycling
• Equipment sized to meet the needs of small users, and the largest industrial plants.
• With new, used, and refurbished options, we can usually find a system to fit your budget.
• Technical help with setting up and training to use the solvent recycling systems
• We won’t forget you after the sale.
# Operating steps
After opening the crate, plug in 220 V power, and connect the ground (earth).
Open the lid and fill the tank up to the level with solvent to be recovered (80 L) Close the lid and tighten it.
Check all the pipe / hose make sure it is well connected. Especially vacuum pipe (6) and fresh come-out pipe(1).
Set up the thermostat(18) for example for Perc.is 150 degree C, for green chemical is 160-210 degree C.
Vacuum tank pressure(3) high at 0.03 Mpa / low at 0.01Mpa, and steam cooling fan thermostat(11) at 40 degree C.
Turn on the power switch(15), steam cooling switch(16), heater switch(17) and vacuum pump switch(12).
If you want to be controlled with timer, it depends on the quantity of the chemical, set up the timer(14) then turn on the switch(13).
Install the unit in a wide and ventilated place
Disconnect electric power before doing any action
No taking off the control panel
Change the diathermic oil every 1000 working hours
No filling the solvent container up over the level (80 liters)
Remove the waste after every recovery process
Recovery Time 3 o 4 hours